logo
Aperçu Nouvelles

IP Rating for Cables Explained: IP44, IP65, IP67 and IP68 in Real Installations

LA CHINE Shanghai Shenghua Cable (Group) Co., Ltd. certifications
LA CHINE Shanghai Shenghua Cable (Group) Co., Ltd. certifications
Gentil fournisseur, réponse de vitesse rapide, délai de livraison rapide, produit de haute qualité. Je suis chanceux pour vous trouver !

—— Forgeron de John

Nous avons été au travail avec ensemble pendant 5 années, ils sommes bon fournisseur et bons amis, notre honneur à travailler avec elles.

—— Mohamed Rebai

Je suis très heureux avec le service de cette société, je crois que leurs affaires seront meilleures et meilleures.

—— Daniel

Votre présentation et service professionnels que vous nous avez donnés ont mérité une ovation debout. Shenghua devrait avoir un avenir plus lumineux.

—— Rendell Brewster

Шенгхуа іс а цредібле энтерпрісэ, ве хве эстаблішед цооператыён фор з ерс анд віл кеп лонг тэрм цооператыён.

—— KHADBAATAR

Je suis en ligne une discussion en ligne
Société Nouvelles
IP Rating for Cables Explained: IP44, IP65, IP67 and IP68 in Real Installations

Summary

An IP rating on a cable is one of the most misused specifications in electrical procurement. Buyers see IP68 cable on a data sheet and assume the installation is protected, while the real protection depends on the gland, the termination and the immersion depth and time that the rating was tested against. This guide decodes the IP code digit by digit, explains what IP44, IP65, IP67 and IP68 actually require, and shows how the rating applies to submersible pumps, mining equipment, marine installations and flood prone pits. It also sets out how to specify a cable and a termination as one sealed system, with six direct answers on testing, gland selection and the difference between waterproof and submersible.

IP68 waterproof PVC insulated power cable 0.6/1kV 4x25mm2 for underground direct burial

What an IP Rating Actually Measures

IP stands for Ingress Protection, and the code has two digits. The first digit rates protection against solid objects, from 0 (no protection) to 6 (dust tight). The second digit rates protection against water, from 0 to 8. The second digit is the one that matters in cable discussions, but it is meaningless without the first, because water protection is impossible if the enclosure admits dust and debris.

  • IP44 - protected against solid objects larger than 1 mm and against water splashing from any direction.
  • IP54 - dust protected and splash proof, common for outdoor junction boxes.
  • IP65 - dust tight and protected against water jets from a 6.3 mm nozzle at 12.5 litres per minute.
  • IP66 - dust tight and protected against powerful water jets.
  • IP67 - dust tight and protected against temporary immersion, typically 1 m for 30 minutes.
  • IP68 - dust tight and suitable for continuous immersion under conditions agreed between manufacturer and user.
RatingWater conditionTypical cable application
IP44Splashing waterOutdoor lighting, sheltered facade
IP65Water jetsMarine deck, wash-down areas
IP67Temporary immersion 1 mMining, wet pits, industrial floors
IP68Continuous immersionSubmersible pumps, wells, fountains

The critical point is that IP68 has no fixed depth or duration in the standard. It is an open category defined by agreement between manufacturer and purchaser, so a supplier claiming IP68 without stating 10 m for 7 days, or 2 m for 24 hours, or any other defined condition has made an unverifiable statement. A proper data sheet states the test condition, the sample length, whether the sample was terminated, and the acceptance criterion, which is normally an insulation resistance measurement and a visual check for water inside the cable.

Why the Rating Is Often Wasted in Practice

Most water ingress failures in IP rated installations are not cable failures at all. They are termination failures. A cable that passes an immersion test as a bare sheathed sample will still fill with water if it is cut, terminated with an unsealed gland, and installed in a wet pit. The rating then becomes a false comfort, and the maintenance team spends months replacing cables that were never the problem.

1. The gland is part of the system. A cable gland must match the cable diameter, the sheath material and the required IP level. A standard IP54 gland on an IP68 cable gives an IP54 termination. Sealed glands with an elastomer compression seal, a sealing washer against the enclosure wall and a proper strain relief are required, and they must be tightened to the specified torque, because an over-tightened gland deforms the sheath and creates a leak path along the sheath surface.

2. Capillary action beats gravity. In a submersible pump cable, water enters at the pump end where the cable is immersed and travels upward inside the stranded conductor, against gravity, until it reaches the control panel. This is why stranded conductors in wet duty must be water blocked, and why the pump end should be potted or sealed with a resin kit rather than simply taped. A cable with water blocking in the conductor resists this path; a cable without it will conduct water into the panel within a season.

3. Depth and pressure. Ten metres of water adds roughly one bar of pressure, and a small defect that leaks nothing at one metre will pass water steadily at ten. The immersion depth in the specification must be the real depth of the installation plus a margin for surge and drawdown, not a nominal figure copied from a catalogue.

4. Cost of failure. A failed submersible pump cable usually means lifting the pump, which in a deep well can cost more than the cable and the pump together. In a mine or a marine installation, the labour and downtime cost dwarf the material price. That asymmetry is the entire argument for specifying the rating with verified test conditions rather than accepting a logo on a brochure.

How to Specify and Install for Real Water Protection

Begin with the environment, not with the code. A cable splashed by rain needs IP44 at most. A cable on a wash-down deck needs IP65 with a sealed gland. A cable in a pit that floods seasonally needs IP67 plus water blocking plus a sealed termination. A cable permanently under water needs IP68 with a stated depth and duration, water blocking in the conductor, and a resin or heat-shrink termination rated for the same conditions.

Write the test into the purchase order. For IP68, require the factory to state the depth, the duration and the sample configuration, and to supply an immersion test report on a finished cable, ideally with a terminated end. Require the insulation resistance after immersion to be above a stated value, and require the internal inspection result. For IP67, a 30 minute immersion at 1 m with a pre-immersion and post-immersion insulation resistance reading is a reasonable acceptance criterion.

Then treat the termination as a separate procurement item. Specify the gland by IP rating and cable diameter range, specify the sealing method at the equipment end, and require the installer to record the torque applied. Where the cable enters a pump or a motor, use the manufacturer termination kit; a generic gland on a submersible pump is a known cause of repeat failure. Leave a drip loop on every vertical entry so that water runs off the cable rather than into the gland, and seal every penetration through a wall or a pit wall with a proper sealed sleeve, not with foam.

Maintenance matters as much as installation. Submersible cables should be insulation resistance tested at each pump service, and the trend recorded. A drop from hundreds of megohms to a few megohms between two services is the earliest sign of sheath damage or gland leakage, and it is far cheaper to replace a gland than a pump. In mining and marine environments, inspect the cable at every scheduled shutdown for crushed sections, abrasion at clamp points and hardening of the sheath, because mechanical damage is the most common precursor to water ingress.

Finally, check the surrounding electrical design. Sealing a cable does not make it suitable for a hazardous area, and an IP68 rating says nothing about flame propagation, chemical resistance or temperature rating. Each of those must be specified separately, and a cable should be selected on the combination rather than on a single headline number.

EnvironmentMinimum cable ratingTermination requirement
Rain exposed wallIP44 sheath, UV stabilisedStandard gland, drip loop
Wash-down areaIP65Sealed gland, torque recorded
Flood prone pitIP67 plus water blockingSealed gland plus resin end
Well or boreholeIP68, stated depthPump kit, potted end
Marine deckIP66 plus tinned copperCorrosion resistant gland

Representative products include the IP68 waterproof PVC insulated cable 4x25mm2 for underground direct burial, the IP68 submersible cable 4x10mm2 for underwater pumps, and the H07RN-F 4x6mm2 rubber sheathed deep well pump cable for flexible riser duty. Industrial and mining circuits are usually served by the VGV 3x6mm2 IP67 waterproof cable, marine and wash-down areas by the VGV 3x1.5mm2 IP65 cable for marine and industrial use, and decorative water features by the H07RN-F 3x2.5mm2 fountain pump submersible cable.

How Water Ingress Tests Are Actually Run

A meaningful immersion test uses a cable sample of a defined length, usually three to five metres, prepared exactly as it will be installed. For an IP67 test the sample is immersed to one metre for thirty minutes; for IP68 the depth and duration are those agreed in the specification, for example ten metres for seven days or two metres for twenty-four hours. Before immersion the insulation resistance is measured and recorded. After immersion the sample is removed, the surface is dried, and the insulation resistance is measured again. A pass requires the value to remain above the acceptance threshold and, on dissection, no water visible inside the sheath or between the cores. Some customers require a dye added to the water so that any ingress path is visible on dissection, which is a simple and very effective way to expose a weak termination.

Jet tests are equally specific. IP65 uses a 6.3 mm nozzle delivering 12.5 litres per minute from a distance of about three metres for at least three minutes, directed at the enclosure from all practical angles. IP66 uses a 12.5 mm nozzle at 100 litres per minute. The point of quoting these numbers is that a supplier who claims IP65 because the cable has a rubber sheath has not performed any of this, and a buyer who writes the test method and the acceptance criterion into the purchase specification has removed the ambiguity entirely.

A Submersible Pump Riser in Practice

Consider a borehole pump at 40 m depth with a 4x6 mm2 riser. The water pressure at the pump is about four bar, the cable is permanently immersed, and the failure mode that matters most is water travelling up the strands into the control panel. The correct construction is a water blocked flexible rubber sheathed cable, a potted or resin sealed termination at the pump end, a stainless steel or heavily galvanised cable clamp every three metres so that the cable weight is carried by the riser pipe rather than by the conductor, and a sealed gland at the panel with a drip loop below it. Insulation resistance should be recorded at installation and at every subsequent service. An installation built this way will normally outlast two pump replacements; an installation built with taped ends and a standard gland will usually fail within the first year, and the repair cost will include lifting the pump a second time.

FAQ

Does IP68 mean the cable can be used in any depth of water?

No. IP68 is defined by agreement between manufacturer and purchaser, and the depth and duration must be stated. A cable rated for 1 m is not automatically suitable for 30 m.

Can I use an IP68 cable with a standard gland?

No. The termination determines the installed rating. An IP54 gland on an IP68 cable produces an IP54 installation, and water will enter through the gland.

What is the difference between IP67 and IP68?

IP67 covers temporary immersion, typically 1 m for 30 minutes. IP68 covers continuous immersion under conditions agreed with the manufacturer, with stated depth and time.

Is water blocking necessary for IP68 cable?

It is strongly recommended. Without conductor blocking, water travels along the strands into the equipment even if the sheath remains intact elsewhere.

How is an IP rating verified on a cable?

By immersion or jet testing of a finished sample, followed by insulation resistance measurement and internal inspection. Ask for the test report with the conditions stated.

Does an IP rating cover chemical or oil resistance?

No. IP ratings address solid objects and water only. Chemical, oil and UV resistance must be specified and tested separately.

Conclusion

An IP rating is a property of the installed system, not of a drum of cable. Choose the rating from the real environment, state the depth and duration for IP68, block the conductor against capillary travel, seal the termination with a gland of the same rating, and record insulation resistance at every service. Do that and the number on the data sheet becomes a measurable guarantee instead of a marketing claim. Shanghai Shenghua Cable Group supplies IP65, IP67 and IP68 power and submersible cable in PVC, XLPE and rubber sheathed constructions, with water blocking options and immersion test documentation. Send your installation depth, ambient conditions and termination arrangement through our contact page and our engineers will match the cable, the gland and the test protocol as one package.

Temps de bar : 2026-11-17 15:32:45 >> Liste de nouvelles
Coordonnées
Shanghai Shenghua Cable (Group) Co., Ltd.

Personne à contacter: Ms. Mayling Zhao

Téléphone: 86-21-68172999

Télécopieur: 86-21-58179888

Envoyez votre demande directement à nous (0 / 3000)